BendPak's HDS-18​E heavy-duty four-post truck lift is for servicing long wheelbase trucks. Bigger sheaves, beefier components and a legacy of dependability--get your hands on these massive truck lifts and bring a higher level of service to your garage or shop. BendPak's HDS-Truck Series four-post hoists are a whole new breed of rugged. They’re newly engineered heavy-duty truck lifts that make light work out of heavy lifting. They work better, are built to last, and feature upgrades that increase safety, durability and productivity.

All HDS-18E standard length truck lifts feature:

• Supersized 12” diameter cable sheaves within the runway and cross tubes combined with massive 4” diameter sheave axles dramatically improve cable wear and critical component lifespan meaning you’ll increase safety and spend less money in service related expenses down the road.


• BendPak's HDS Truck Series lifts feature ​4 stainless-steel lifting cables that provide great balance between abrasion resistance and fatigue.


• Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze.
   
• Each HDS Truck Series four-post lift is equipped with a single hydraulic cylinder hidden away under the runway for maximum performance and minimum exposure to elements. The hydraulic cylinder features high-durometer rod seals, pressure loaded U-cup piston seals, backups and wear bands that virtually eliminate any fluid bypass. The welded cylinder body is made from high strength steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures straight, smooth, cylinders that will provide years and years of dependable trouble-free service.

• 12" x 12" base plates provide a solid foundation.


• Non-skid runways provides maximum grip, even when the runway surface is wet or oily.

• Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze.

• Spring-loaded safety locks automatically engage continuously during rise and adjustable safety ladders allow for precise runway leveling even when installed on sloped floors.

• A secondary lock system is on constant guard and acts as a slack-cable device in the unlikely event of an unexpected cable failure.

• A maintenance-free electric hydraulic power system assures ultimate dependability.

• A simple push-button pneumatic lock release makes lowering operations simple and fast. Aircraft-quality stainless steel and aluminum pneumatic cylinders will provide years of trouble-free service.

• Optional Rolling jacks are used to raise the front or rear portion of a vehicle off the runways allowing operators to perform efficient wheel and break service. Each jack has telescoping arms and frame contact pads that can be extended over the runways and positioned under vehicle lifting points. Each jack features three safety-lock positions and stack-able truck and van adapters for increased lifting height and better access to frame contact points on high ground-clearance vehicles. A pair of jacks allows the entire vehicle to elevated. The jacks come equipped with a commercial grade air-hydraulic pump.

*NOTE: Not all car lift models sold by Wrenchers Warehouse meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201. User or Buyer assumes full responsibility for any state, county, federal or international mandated permit, license, code, standard, certification, or any other mandate required related to the installation and/or operation of the car lift. Read full General Disclaimer details.

• • Lifting capacity*: 18,000 lbs.
    • *Max capacity / front axle: 9,000 lbs.
    • *Max capacity / rear axle: 9,000 lbs.
  • Overall width: 154"
  • Outside length: 257"
  • Overall length: 297"
  • Height of columns: 93"
  • Runway min height: 8-1/2" 
  • Max rise: 60"
  • Max lifting height: 68-1/2"
  • Width between posts: 134"
  • Runway width: 22"
  • Width between runways: 38" – 56"
  • Runway center line: 60" - 78"
  • Outside edge of runways: 82" - 100"
  • Drive-thru clearance: 109"
  • Length of runways: 263"
  • Min wheelbase @ rated capacity: 185"
  • Min wheelbase @ 75% capacity: 160"
  • Min wheelbase @ 50% capacity: 135"
  • Min wheelbase @ 25% capacity: 110"
  • Locking positions: 9
  • Lock spacing: every 6"
  • Lifting time: 75 sec
  • Motor: 220 VAC / 60 Hz / 1 Ph
  • Shipping weight: 4,895 lbs.

  ​

  Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*NOTE: Not all car lift models sold by Wrenchers Warehouse meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201. User or Buyer assumes full responsibility for any state, county, federal or international mandated permit, license, code, standard, certification, or any other mandate required related to the installation and/or operation of the car lift. Read full General Disclaimer details.